solution.h

Go to the documentation of this file.

/**************************************************************************/ /**
 * @brief Platform position/attitude solution messages.
 * @file
 ******************************************************************************/
 
#pragma once
 
#include "point_one/fusion_engine/common/portability.h"
#include "point_one/fusion_engine/messages/defs.h"
 
namespace point_one {
namespace fusion_engine {
namespace messages {
 
// Enforce 4-byte alignment and packing of all data structures and values.
// Floating point values are aligned on platforms that require it. This is done
// with a combination of setting struct attributes, and manual alignment
// within the definitions. See the "Message Packing" section of the README.
#pragma pack(push, 1)
 
/**
 * @defgroup solution_messages Navigation Solution Message Definitions
 * @brief Output messages containing position, navigation, and time results.
 * @ingroup messages
 *
 * See also @ref messages.
 */
 
/**
 * @brief Platform pose solution: position, velocity, attitude (@ref
 *        MessageType::POSE, version 1.2).
 * @ingroup solution_messages
 *
 * @note
 * All data is timestamped using Point One (P1) time, which is a monotonic
 * timestamp referenced to the start of the device. Corresponding messages (@ref
 * GNSSInfoMessage, @ref GNSSSatelliteMessage, etc.) may be associated using
 * their @ref p1_time values.
 */
struct P1_ALIGNAS(4) PoseMessage : public MessagePayload {
  static constexpr MessageType MESSAGE_TYPE = MessageType::POSE;
  static constexpr uint8_t MESSAGE_VERSION = 2;
  static constexpr int16_t INVALID_UNDULATION = INT16_MIN;
 
  /** Set if the device is stationary. */
  static constexpr uint8_t FLAG_STATIONARY = 0x01;
 
  /** The time of the message, in P1 time (beginning at power-on). */
  Timestamp p1_time;
 
  /** The GPS time of the message, if available, referenced to 1980/1/6. */
  Timestamp gps_time;
 
  /** The type of this position solution. */
  SolutionType solution_type;
 
  /**
   * A bitmask of flags associated with the pose data.
   *
   * Added in @ref PoseMessage version 1.2.
   */
  uint8_t flags = 0x0;
 
  /**
   * The geoid undulation at the current location (in cm).
   *
   * Geoid undulation is also frequently referred to as "geoid height". It is
   * the height of the MSL geoid above the WGS-84 ellipsoid. Note that it is
   * independent of the location of the receiver.
   *
   * Receiver ellipsoid altitude reported in @ref lla_deg (also frequently
   * called "height above the ellipsoid") can be converted to a corresponding
   * mean sea level (MSL) altitude ("height above the geoid" or "orthometric
   * height") as follows:
   *
   * @f[
   * h_{orthometric} = h_{ellipsoid} - undulation
   * @f]
   *
   * Stored in units of 0.01 meters: `undulation_m = undulation_cm * 0.01`. Set
   * to `-32768` if invalid.
   *
   * Added in @ref PoseMessage version 1.1.
   */
  int16_t undulation_cm = INVALID_UNDULATION;
 
  /**
   * The geodetic latitude, longitude, and altitude (in degrees/degrees/meters),
   * expressed using the WGS-84 reference ellipsoid.
   *
   * @section p1_fe_pose_datum Datum/Epoch Considerations
   * When comparing two positions, it is very important to make sure they are
   * compared using the same geodetic datum, defined at the same time (epoch).
   * Failing to do so can cause very large unexpected differences since the
   * ground moves in various directions over time due to motion of tectonic
   * plates.
   *
   * For example, the coordinates for a point on the ground in San Francisco
   * expressed in the ITRF14 datum may differ by multiple meters from the
   * coordinates for the same point expressed the NAD83 datum. Similarly, the
   * coordinates for that location expressed in the ITRF14 2017.0 epoch
   * (January 1, 2017) may differ by 12 cm or more when expressed using the
   * ITRF14 2021.0 epoch (January 1, 2021).
   *
   * The datum and epoch to which the position reported in this message is
   * aligned depends on the current @ref solution_type.
   * - @ref SolutionType::AutonomousGPS / @ref SolutionType::DGPS /
   *   @ref SolutionType::PPP - Standalone solutions (i.e., no differential
   *   corrections) are aligned to the WGS-84 datum as broadcast live by GPS
   *   (aligns closely with the ITRF08/14 datums).
   * - @ref SolutionType::RTKFloat / @ref SolutionType::RTKFixed - When
   *   differential corrections are applied, the reference datum and epoch are
   *   defined by the corrections provider. Point One's Polaris Corrections
   *   Service produces corrections using the ITRF14 datum. See
   *   https://pointonenav.com/polaris for more details.
   * - @ref SolutionType::Integrate - When the INS is dead reckoning in the
   *   absence of GNSS, vision, or other measurements anchored in absolute world
   *   coordinates, the position solution is defined in the same datum/epoch
   *   specified by the previous solution type (e.g., WGS-84 if previously
   *   standalone GNSS, i.e., @ref SolutionType::AutonomousGPS).
   */
  double lla_deg[3] = {NAN, NAN, NAN};
 
  /**
   * The position standard deviation (in meters), resolved with respect to the
   * local ENU tangent plane: east, north, up.
   */
  float position_std_enu_m[3] = {NAN, NAN, NAN};
 
  /**
   * The platform attitude (in degrees), if known, described as intrinsic
   * Euler-321 angles (yaw, pitch, roll) with respect to the local ENU tangent
   * plane. Set to `NAN` if attitude is not available.
   *
   * @note
   * The platform body axes are defined as +x forward, +y left, and +z up. A
   * positive yaw is a left turn, positive pitch points the nose of the vehicle
   * down, and positive roll is a roll toward the right. Yaw is measured from
   * east in a counter-clockwise direction. For example, north is +90 degrees
   * (i.e., `heading = 90.0 - ypr_deg[0]`).
   */
  double ypr_deg[3] = {NAN, NAN, NAN};
 
  /**
   * The attitude standard deviation (in degrees): yaw, pitch, roll.
   */
  float ypr_std_deg[3] = {NAN, NAN, NAN};
 
  /**
   * The platform velocity (in meters/second), resolved in the body frame. Set
   * to `NAN` if attitude is not available for the body frame transformation.
   */
  double velocity_body_mps[3] = {NAN, NAN, NAN};
 
  /**
   * The velocity standard deviation (in meters/second), resolved in the body
   * frame.
   */
  float velocity_std_body_mps[3] = {NAN, NAN, NAN};
 
  /** The estimated aggregate 3D protection level (in meters). */
  float aggregate_protection_level_m = NAN;
  /** The estimated 2D horizontal protection level (in meters). */
  float horizontal_protection_level_m = NAN;
  /** The estimated vertical protection level (in meters). */
  float vertical_protection_level_m = NAN;
};
 
/**
 * @brief Auxiliary platform pose information (@ref MessageType::POSE_AUX,
 *        version 1.0).
 * @ingroup solution_messages
 */
struct P1_ALIGNAS(4) PoseAuxMessage : public MessagePayload {
  static constexpr MessageType MESSAGE_TYPE = MessageType::POSE_AUX;
  static constexpr uint8_t MESSAGE_VERSION = 0;
 
  /** The time of the message, in P1 time (beginning at power-on). */
  Timestamp p1_time;
 
  /**
   * The position standard deviation (in meters), resolved in the body frame.
   * Set to `NAN` if attitude is not available for the body frame
   * transformation.
   */
  float position_std_body_m[3] = {NAN, NAN, NAN};
 
  /**
   * The 3x3 position covariance matrix (in m^2), resolved in the local ENU
   * frame. Values are stored in row-major order.
   */
  double position_cov_enu_m2[9] = {NAN};
 
  /**
   * The platform body orientation with respect to the local ENU frame,
   * represented as a quaternion with the scalar component last (x, y, z, w).
   */
  double attitude_quaternion[4] = {NAN, NAN, NAN, NAN};
 
  /**
   * The platform velocity (in meters/second), resolved in the local ENU frame.
   */
  double velocity_enu_mps[3] = {NAN, NAN, NAN};
 
  /**
   * The velocity standard deviation (in meters/second), resolved in the local
   * ENU frame.
   */
  float velocity_std_enu_mps[3] = {NAN, NAN, NAN};
};
 
/**
 * @brief Information about the GNSS data used in the @ref PoseMessage with the
 *        corresponding timestamp (@ref MessageType::GNSS_INFO, version 1.1).
 * @ingroup solution_messages
 *
 * @note
 * The deprecated `last_differential_time` field was removed in version 1.1 of
 * this message, and was replaced by the new @ref leap_second, @ref num_svs,
 * @ref corrections_age, and @ref baseline_distance fields. Attempting to use
 * those fields on version 0 messages will result in undefined behavior.
 */
struct P1_ALIGNAS(4) GNSSInfoMessage : public MessagePayload {
  static constexpr MessageType MESSAGE_TYPE = MessageType::GNSS_INFO;
  static constexpr uint8_t MESSAGE_VERSION = 1;
 
  static constexpr uint16_t INVALID_LEAP_SECOND = 0xFF;
  static constexpr uint16_t INVALID_AGE = 0xFFFF;
  static constexpr uint16_t INVALID_DISTANCE = 0xFFFF;
  static constexpr uint32_t INVALID_REFERENCE_STATION = 0xFFFFFFFF;
 
  /** The time of the message, in P1 time (beginning at power-on). */
  Timestamp p1_time;
 
  /** The GPS time of the message, if available, referenced to 1980/1/6. */
  Timestamp gps_time;
 
  /**
   * The current UTC leap second (offset between UTC and GPS time), if known.
   * Set to 0xFF if invalid.
   *
   * Added in message version 1.
   */
  uint8_t leap_second = INVALID_LEAP_SECOND;
 
  /** The number of satellites used in the current position solution. */
  uint8_t num_svs = 0;
 
  uint8_t reserved[2];
 
  /**
   * The age of the most recently received GNSS corrections data (in 0.1
   * seconds). Set to 0xFFFF if invalid.
   *
   * Added in message version 1.
   */
  uint16_t corrections_age = INVALID_AGE;
 
  /**
   * The distance between the device and the GNSS corrections base station.
   * Stored in units of 10 meters:
   * `baseline_distance_m = baseline_distance * 10`. Set to 0xFFFF if invalid.
   *
   * Added in message version 1.
   */
  uint16_t baseline_distance = INVALID_DISTANCE;
 
  /**
   * The ID of the GNSS corrections base station, if used. Set to 0xFFFFFFFF if
   * invalid.
   */
  uint32_t reference_station_id = INVALID_REFERENCE_STATION;
 
  /** The geometric dilution of precision (GDOP). */
  float gdop = NAN;
  /** The position dilution of precision (PDOP). */
  float pdop = NAN;
  /** The horizontal dilution of precision (HDOP). */
  float hdop = NAN;
  /** The vertical dilution of precision (VDOP). */
  float vdop = NAN;
 
  /** GPS time alignment standard deviation (in seconds). */
  float gps_time_std_sec = NAN;
};
 
/**
 * @brief Information about the individual satellites used in the @ref
 *        PoseMessage and @ref GNSSInfoMessage with the corresponding timestamp
 *        (@ref MessageType::GNSS_SATELLITE, version 1.0).
 * @ingroup solution_messages
 *
 * This message is followed by `N` @ref SatelliteInfo objects, where `N` is
 * equal to @ref num_satellites. For example, a message with two satellites
 * would be serialized as:
 *
 * ```
 * {MessageHeader, GNSSSatelliteMessage, SatelliteInfo, SatelliteInfo, ...}
 * ```
 */
struct P1_ALIGNAS(4) GNSSSatelliteMessage : public MessagePayload {
  static constexpr MessageType MESSAGE_TYPE = MessageType::GNSS_SATELLITE;
  static constexpr uint8_t MESSAGE_VERSION = 0;
 
  /** The time of the message, in P1 time (beginning at power-on). */
  Timestamp p1_time;
 
  /** The GPS time of the message, if available, referenced to 1980/1/6. */
  Timestamp gps_time;
 
  /** The number of known satellites. */
  uint16_t num_satellites = 0;
 
  uint8_t reserved[2] = {0};
};
 
/**
 * @brief Information about an individual satellite (see @ref
 *        GNSSSatelliteMessage).
 *
 * For satellites where @ref usage is 0, the satellite may either be currently
 * tracked by the receiver but not used for navigation, or may just be expected
 * according to available ephemeris data.
 */
struct P1_ALIGNAS(4) SatelliteInfo {
  /**
   * @defgroup satellite_usage Bit definitions for the satellite usage bitmask
   *           (@ref SatelliteInfo::usage).
   * @{
   */
  static constexpr uint8_t SATELLITE_USED = 0x01;
  /** @} */
 
  static constexpr int16_t INVALID_CN0 = 0;
 
  /** The GNSS system to which this satellite belongs. */
  SatelliteType system = SatelliteType::UNKNOWN;
 
  /** The satellite's PRN (or slot number for GLONASS). */
  uint8_t prn = 0;
 
  /**
   * A bitmask specifying how this satellite was used in the position solution.
   * Set to 0 if the satellite was not used. See @ref satellite_usage.
   */
  uint8_t usage = 0;
 
  /**
   * The carrier-to-noise density ratio (C/N0) for the L1 signal on the
   * satellite.
   *
   * Stored in units of 0.25 dB-Hz: `cn0_dbhz = cn0 * 0.25`. Set to 0 if
   * invalid. The range of this field is 0.25-63.75 dB-Hz. Values outside of
   * this range will be clipped to the min/max values.
   *
   * @note
   * If the satellite is not tracking L1 (or the L1-equivalent for other
   * constellations, e.g., G1 for GLONASS) but another frequency is being used,
   * that signal's C/N0 value will be reported.
   *
   * Added in @ref GNSSSatelliteMessage version 1.1.
   */
  uint8_t cn0 = INVALID_CN0;
 
  /** The azimuth of the satellite (in degrees). */
  float azimuth_deg = NAN;
 
  /** The elevation of the satellite (in degrees). */
  float elevation_deg = NAN;
};
 
/**
 * @brief The stages of the device calibration process.
 * @ingroup solution_messages
 */
enum class CalibrationStage : uint8_t {
  UNKNOWN = 0, ///< Calibration stage not known.
  MOUNTING_ANGLE = 1, ///< Estimating IMU mounting angles.
  DONE = 255, ///< Calibration complete.
};
 
/**
 * @brief Get a human-friendly string name for the specified @ref
 *        CalibrationStage.
 *
 * @param val The enum to get the string name for.
 *
 * @return The corresponding string name.
 */
P1_CONSTEXPR_FUNC const char* to_string(CalibrationStage val) {
  switch (val) {
    case CalibrationStage::UNKNOWN:
      return "Unknown";
    case CalibrationStage::MOUNTING_ANGLE:
      return "IMU Mounting Angles";
    case CalibrationStage::DONE:
      return "Done";
    default:
      return "Unrecognized";
  }
}
 
/**
 * @brief @ref CalibrationStage stream operator.
 */
inline p1_ostream& operator<<(p1_ostream& stream, CalibrationStage val) {
  stream << to_string(val) << " (" << (int)val << ")";
  return stream;
}
 
/**
 * @brief Device calibration status update. (@ref
 *        MessageType::CALIBRATION_STATUS, version 1.1).
 * @brief
 * @ingroup solution_messages
 */
struct P1_ALIGNAS(4) CalibrationStatusMessage : public MessagePayload {
  static constexpr MessageType MESSAGE_TYPE = MessageType::CALIBRATION_STATUS;
  static constexpr uint8_t MESSAGE_VERSION = 1;
 
  /** The most recent P1 time, if available. */
  Timestamp p1_time;
 
  /**
   * @name Calibration State Data
   * @{
   */
 
  /** The current calibration stage. */
  CalibrationStage calibration_stage = CalibrationStage::UNKNOWN;
 
  uint8_t reserved1[3] = {0};
 
  /** The IMU yaw, pitch, and roll mounting angle offsets (in degrees). */
  float ypr_deg[3] = {NAN, NAN, NAN};
 
  /**
   * The IMU yaw, pitch, and roll mounting angle standard deviations (in
   * degrees).
   */
  float ypr_std_dev_deg[3] = {NAN, NAN, NAN};
 
  /** The accumulated calibration travel distance (in meters). */
  float travel_distance_m = 0.0;
 
  uint8_t reserved2[24] = {0};
 
  /** @} */
 
  /**
   * @name Calibration Process Status
   * @{
   */
 
  /**
   * Set to 1 once the navigation engine state is validated after
   * initialization.
   */
  uint8_t state_verified{0};
 
  uint8_t reserved3[3] = {0};
 
  /**
   * The completion percentage for gyro bias estimation, stored with a
   * scale factor of 0.5% (0-200).
   */
  uint8_t gyro_bias_percent_complete = 0;
 
  /**
   * The completion percentage for accelerometer bias estimation, stored with a
   * scale factor of 0.5% (0-200).
   */
  uint8_t accel_bias_percent_complete = 0;
 
  /**
   * The completion percentage for IMU mounting angle estimation, stored with a
   * scale factor of 0.5% (0-200).
   */
  uint8_t mounting_angle_percent_complete = 0;
 
  uint8_t reserved4[5] = {0};
 
  /** @} */
 
  /**
   * @name Calibration Thresholds
   * @{
   */
 
  /**
   * The minimum accumulated calibration travel distance needed to complete
   * mounting angle calibration.
   */
  float min_travel_distance_m = NAN;
 
  /**
   * The max threshold for each of the YPR mounting angle states (in degrees),
   * above which calibration is incomplete.
   */
  float mounting_angle_max_std_dev_deg[3] = {NAN, NAN, NAN};
 
  /** @} */
};
 
/**
 * @brief Relative ENU position to base station (@ref
 *        MessageType::RELATIVE_ENU_POSITION, version 1.1).
 * @ingroup solution_messages
 *
 * @note
 * This message represents the relationship between the navigation engine's
 * position solution and a nearby RTK base station. It is not used to convey
 * unfiltered vehicle body orientation measurements generated using multiple
 * GNSS antennas. See @ref GNSSAttitudeOutput instead.
 */
struct P1_ALIGNAS(4) RelativeENUPositionMessage : public MessagePayload {
  static constexpr MessageType MESSAGE_TYPE =
      MessageType::RELATIVE_ENU_POSITION;
  static constexpr uint8_t MESSAGE_VERSION = 1;
 
  static constexpr uint32_t INVALID_REFERENCE_STATION = 0xFFFFFFFF;
 
  /** The time of the message, in P1 time (beginning at power-on). */
  Timestamp p1_time;
 
  /** The GPS time of the message, if available, referenced to 1980/1/6. */
  Timestamp gps_time;
 
  /** The type of this position solution. */
  SolutionType solution_type = SolutionType::Invalid;
 
  uint8_t reserved[3] = {0};
 
  /** The ID of the differential base station. */
  uint32_t reference_station_id = INVALID_REFERENCE_STATION;
 
  /**
   * The relative position (in meters), resolved in the local ENU frame.
   *
   * @note
   * If a differential solution to the base station is not available, these
   * values will be `NAN`.
   */
  double relative_position_enu_m[3] = {NAN, NAN, NAN};
 
  /**
   * The position standard deviation (in meters), resolved with respect to the
   * local ENU tangent plane: east, north, up.
   *
   * @note
   * If a differential solution to the base station is not available, these
   * values will be `NAN`.
   */
  float position_std_enu_m[3] = {NAN, NAN, NAN};
};
 
#pragma pack(pop)
 
} // namespace messages
} // namespace fusion_engine
} // namespace point_one